Super7 Drinkware and Apparel: Washing and Care Essentials
By Super7 | Action Figures & Collectible Toys | Published: 2026-10-16
Category: Tips & Care
Keep your Super7 graphic tees and collectible drinkware looking sharp with a simple wash-and-care routine that protects prints, colors, and coatings.
Quick answer
Wash Super7 graphic tees inside out in cold water on a gentle cycle, then hang or lay flat to dry. Hand-wash collectible drinkware with mild soap and a soft sponge, and never put printed or coated cups in the dishwasher. These two habits prevent the most common damage: cracked prints and faded coatings.
Why the care routine differs for tees and drinkware
Super7 apparel and drinkware share a common enemy: heat. Hot water, high dryer temperatures, and dishwasher cycles break down the inks and coatings that make collectible designs look sharp. A graphic tee like the G.I. Joe T-Shirt - U.S.S. FLAGG or the Rugrats Reptar T-Shirt uses screen-printed or direct-to-garment decoration that sits on top of the fabric, so abrasion and heat wear it away faster than the cotton itself. Drinkware with printed logos or coated finishes behaves the same way: the decoration is the fragile part, not the mug or cup body.
That means you can treat the base material normally but need to protect the surface. The steps below separate the two routines so you do not accidentally apply a garment habit to a collectible cup.
What to check before the first wash
Look at the care tag and the decoration. If a tee has a Super7 hem tag, that tag confirms the garment construction but does not replace the printed care instructions. For drinkware, check whether the design is printed on the outside, wrapped around the rim, or applied as a decal. Any raised or glossy surface should be treated as delicate.
One common mistake is assuming a pre-shrunk cotton tee cannot shrink further. Pre-shrunk cotton like the SpectraUSA 3100 used for the Rugrats Reptar T-Shirt resists most shrinkage, but high dryer heat can still distort the fit and stress the print. Air drying removes that risk entirely.
Step-by-step washing and care routine
- Turn the tee inside out and zip any zippers: Turning a graphic tee inside out puts the fabric between the print and the drum, which reduces rubbing. If you are washing a tee with a zipper or buttons, close them so they do not snag the knit. Checkpoint: the printed side should face inward before the shirt goes into the machine.
- Wash in cold water on a gentle or delicate cycle: Use a mild detergent without bleach or fabric softener. Cold water protects the dye in the cotton and the ink in the print. Wash similar colors together, and avoid overloading the drum so shirts can move freely. Common mistake: using hot water or a heavy-duty cycle, which fades prints and can shrink even pre-shrunk cotton.
- Skip the dryer and air dry instead: Hang the tee by the shoulders or lay it flat on a drying rack. If you must use a dryer, choose the lowest heat setting and remove the shirt while it is still slightly damp. Checkpoint: high heat is the fastest way to crack a screen print, so air drying is the safest default.
- Hand-wash drinkware with mild soap and a soft sponge: Fill the cup with warm, not hot, water and add a drop of dish soap. Wipe the outside gently with a soft sponge, then rinse thoroughly. Do not use abrasive scrubbers, steel wool, or scouring powder on printed or coated areas. Common mistake: soaking a printed cup for hours, which can lift the design at the edges.
- Dry drinkware upside down on a rack: Let the cup air dry completely before stacking it against another cup. Moisture trapped between stacked cups can cloud a coating or encourage odor. Checkpoint: if the cup has a lid or straw, hand-wash those parts separately and let them dry fully.
- Store tees folded and cups unstacked: Fold graphic tees so the print does not crease against itself, and store them away from direct sunlight. Keep collectible cups on a shelf with a little space between them rather than nesting them rim to rim. Next step: rotate your most-worn pieces to the front so you are not repeatedly washing the same shirt or cup.
Product care facts
- Rugrats Reptar T-Shirt: Printed on a SpectraUSA 3100 pre-shrunk 100% cotton unisex Gold t-shirt that is machine washable, available in sizes S-3X with a Super7 hem tag and shoulder-to-shoulder self jersey neck tape and seamless sides. The pre-shrunk cotton and reinforced neck tape tolerate gentle machine washing, but the printed Reptar graphic still needs cold water and low abrasion to stay intact.
- G.I. Joe T-Shirt - U.S.S. FLAGG: Officially licensed Super7 x G.I. Joe design featuring the iconic U.S.S. FLAGG, available in sizes XS through 4X. The wide size range means you may own several copies; washing them inside out and air drying keeps the licensed artwork from cracking across the large front print.
